This can be achieved by combining these two techniques. To have complete control over DC motor we have to control its speed and rotation direction. ending_eNB_id must be a Hexadecimal number between 0x1 and 0xFFFFFFF.One of the easiest and inexpensive way to control stepper motors is to interface L293D Motor Driver IC with Arduino. To ending_eNB_id: Specifies the last eNB ID in the range. starting_eNB_id must be a Hexadecimal number between 0x1 and 0xFFFFFFF. IDs can be configured only in two eNB groups.Įnb-id-range : Specifies the range of discrete eNB IDs.įrom starting_eNB_id: Specifies the starting eNB ID in the range. Only two eNB ID lists can be configured such that discrete eNB Per eNB ID list and across eNB ID list cannot be configured. However, if 200 eNB IDs are already configured, further enb-id-range configurations are not allowed. The enb-id-range can be a maximum of 64 per configured eNB ID discrete_eNB_id must be a Hexadecimal number between 0x1 and 0xFFFFFFF.Ī maximum of 200 eNB IDs can be configured in an eNB id list. enbid_list_name must be a string of size string of size 1 to 64.Įnb-id discrete_eNB_id: Specifies the discrete eNB IDs. No : Disables the configuration of discrete eNB IDs.Įnbid-list enbid_list_name: Specifies eNB ID list with discrete eNB IDs. configure lte-policy enbid-list enbid_list_name enb-id discrete_eNB_id | enb-id-range from starting_eNB_id to ending_eNB_id end Use the following commands to configure discrete eNB IDs to be used in the eNB group. network_identifier_name, This must be a hexadecimal number between 0x0 and 0xFFFFFFF.Ī maximum of 20 eNB groups can be configured at a time. Global-enb-id prefix network_identifier_name bits bits: Specifies the Global eNB ID prefix that contains a bit string which should be matched with Hexadecimal value. In an eNB Group, it is recommended to configure either Global eNB ID prefix or discrete eNB IDs, it is not recommended to enbid_list_name must be a string of size 1 to 64. configure lte-policy enb-group enb_group_name global-enb-id endĮnbid-list enbid_list_name: Specifies the eNB ID list with discrete eNB IDs. Use the following configuration to configure discrete eNB IDs in the eNB group. Adding the eNB ID List in the eNB Group.This section provides information on the newly introduced CLI commands to configure discrete eNB IDs to the eNB Group in MME. The MME sends the MME Configuration Update message to those eNBs configured in that eNB group. Whenever the relative MME capacity for that eNB group is changed, That eNB group, in the S1 setup response to those eNBs. When the discrete eNB IDs are added to the eNB group, the MME sends the relative MME capacity value, which is configured in This feature is not fully qualified in this release, and is available only for testing purposes. Uneven Distribution of eNodeBs in MME ManagersĪdding Discrete eNB IDs to eNB Group in MMEįeature Summary and Revision History Summary DataĮNB Group configuration recommendation note is added.Target MME Load Balancing During Handover.State-Location Information Retrieval Flag.Handling Call Drop in Smart Watch and Multi-SIM Devices.S-GW Address Based Combined SPGW Selection.Sending EMM Information during Periodic TAU.MO Voice Call and MO Exception Data Support.MME Support for EN-DC SON Configuration Transfer IE on S1-AP.MME Bearer Request Message During Handover Process.No IMSI or MSISDN Included in LRR for VoLTE EM Call from User of Foreign Network.IMEI Check during Periodic TAU Support for NB IoT Devices.HSS and AuC Interworking Configuration Enhancement.GTPV1/V2 Echo Support for Peer MME and SGSN.Excluding SGWs During Relocation Procedures.eNB Group Based Relative Capacity Transmission.Enabling EMM and ESM Cause Code Mapping.Counters for Reason 50/51 on MME and TAI Level.Controlling IMS Voice Over PS Session in S1 Mode.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |